<br><font size=2 face="sans-serif">For most PCs we have here (mainly Dell)
you can go into the BIOS (at startup)</font>
<br><font size=2 face="sans-serif">and change the power setting so that
after a power failure it will automatically</font>
<br><font size=2 face="sans-serif">boot up rather stay off which is the
factory default.</font>
<br>
<br><font size=2 face="sans-serif">David Wilson<br>
USGS Hawaiian Volcano Observatory<br>
dwilson@usgs.gov<br>
</font>
<br>
<br>
<br>
<table width=100%>
<tr valign=top>
<td width=40%><font size=1 face="sans-serif"><b>&quot;Gray Jensen&quot;
&lt;gjensen@usgs.gov&gt;</b> </font>
<br><font size=1 face="sans-serif">Sent by: anss-netops-bounces@geohazards.usgs.gov</font>
<p><font size=1 face="sans-serif">10/28/2008 07:11 AM</font>
<td width=59%>
<table width=100%>
<tr valign=top>
<td>
<div align=right><font size=1 face="sans-serif">To</font></div>
<td><font size=1 face="sans-serif">&quot;ANSS NetOps&quot; &lt;anss-netops@geohazards.usgs.gov&gt;</font>
<tr valign=top>
<td>
<div align=right><font size=1 face="sans-serif">cc</font></div>
<td>
<tr valign=top>
<td>
<div align=right><font size=1 face="sans-serif">Subject</font></div>
<td><font size=1 face="sans-serif">[ANSS-netops] Getting your PC to autoboot
after a power interruption</font></table>
<br>
<table>
<tr valign=top>
<td>
<td></table>
<br></table>
<br>
<br>
<br><font size=2><tt>For those of you that operate remote Earthworm systems
or other<br>
unattended 24/7 PCs, you may have encountered the problem of<br>
the system not rebooting itself when power returns after a power<br>
loss. &nbsp;This is due to fact that current PCs require that the power<br>
pushbutton on the front of the computer be pushed once power is<br>
available. &nbsp;Even if you have a UPS and/or a backup generator, <br>
sometimes they run out or fail to work or somebody accidentally<br>
bumps into your power strip and causes power to go off. &nbsp;On<br>
more than one occasion we have had to send someone hours<br>
away to simply push the &quot;On&quot; button and then drive back.<br>
<br>
The solution is to modify the power supply in the computer to<br>
alway be on when the main power switch in the back is on.<br>
The ATX power supply has an input signal called /PS_ON that<br>
allows the motherboard to turn the supply's power on and off.<br>
It does this by grounding the line. &nbsp;The power supply can be<br>
made to be always on by permanently shorting the line to <br>
ground. &nbsp;/PS_ON is pin 14 on the motherboard power <br>
connector and is usually the green wire. &nbsp;Ground is available<br>
on a number of the wires including pin 15 which is black. &nbsp;<br>
Tying these two together will do the trick.<br>
<br>
To see detailed instructions on how to make this modification,<br>
FTP to the address below.<br>
<br>
ftp://ehzftp.wr.usgs.gov/gjensen/Autoboot.pdf<br>
<br>
Gray Jensen<br>
USGS<br>
Menlo Park, CA<br>
gjensen@usgs.gov<br>
<br>
<br>
_______________________________________________<br>
ANSS-netops mailing list<br>
ANSS-netops@geohazards.usgs.gov<br>
https://geohazards.usgs.gov/mailman/listinfo/anss-netops<br>
</tt></font>
<br>